Skip to content

RF LNA Design Review Freelancer for an Automotive GPS and Digital Radio Circuit

An LNA design review freelancer is needed to independently check an existing automotive RF front end for GPS and digital radio. The client wants a critical review of architecture, matching, biasing, noise and layout, rather than a redesign from scratch.

  • Open · checked 12 Nov 2026
  • Electronics
Budget€30–250 EUR
TimelineNot stated
Skills asked6
Posted2 weeks ago

Is the budget fair? The budget of €30–250 EUR looks workable if the review covers the design files and ends in a written summary. It looks tight if the client also expects measurement support or a circuit redesign.

What the client needs

  • Show experience reviewing RF low-noise amplifier designs for automotive use.
  • Review matching networks, biasing and stability.
  • Check gain, noise figure and isolation between the two radio paths.
  • Give written findings with layout recommendations.

Skills the client asked for: Electronics, Electrical Engineering, PCB Layout, Circuit Design, Signal Processing, Automotive Engineering.

Where to aim your bid

Low€65
Sweet spot€120
High€185

The sweet spot sits about 40% of the way up the client's range, the same rule AutoBidPilot uses for its own price suggestions. Go higher when the scope is large or unclear; go lower only when you can show close, finished work. Check what you keep after fees with the bid price calculator.

What the project involves

The client has an existing RF and LNA design for an automotive application with two frequency paths, GPS and digital radio. The task is an independent, critical design review, not a redesign from scratch.

Areas to review

  • RF architecture and signal paths
  • Input and output matching networks
  • LNA biasing and stability
  • Gain and noise figure
  • Filters and LC networks
  • Isolation between the GPS and digital radio paths
  • PIN diode implementation and RF input protection
  • Strong-signal behaviour, saturation and intermodulation
  • Supply decoupling and grounding
  • PCB layout recommendations
  • Component selection and tolerances

Deliverable and applicant requirements

The expected output is a concise technical report listing potential problems, their severity, recommended changes, and the measurements or simulations needed to validate the design.

Only engineers with practical RF hardware experience should apply. Proposals should briefly describe previous LNA, GNSS or RF front-end designs and the measurement equipment used, such as a VNA, spectrum analyser or noise figure measurement setup.

How to win this project

  1. Name the simulation or measurement tools you would use to check stability, gain and noise figure.
  2. Propose a review order that starts with architecture and signal paths, since the client listed those first.
  3. Explain how you would assess strong-signal behaviour and PIN diode protection, which the client flagged as risk areas.

Questions to ask the client

A specific question in your first message shows you read the brief. Pick one or two:

  • Do you have schematics, layout files and measured data to share?
  • What target frequencies and noise figure limit apply?
  • Should the review be a written report, marked-up files or a call?

Common questions

How much does an LNA design review freelancer cost?

The listed budget is €30–250 EUR. That range fits a focused review of one circuit, but a deep check of the layout and measurements may need more.

What skills does an LNA design review need?

RF circuit design, PCB layout, matching networks, and noise and gain analysis for automotive radio paths.

Is this project still open?

We checked this project on 10 November 2026. Projects get awarded, so apply soon; we take a brief down when it closes.

This page is our own summary of a project posted online, written to help you decide and to write a better bid. Projects get awarded or closed, so apply soon; we take a brief down when it closes. No job or income is guaranteed.

Before you apply

To apply for this job you need a free AutoBidPilot account. It takes about a minute:

  1. Create your account with your email, Google or GitHub.
  2. Verify your email. We send you a link; opening it brings you straight back to this job.
  3. Finish a short setup (your skills and pricing), then apply.
Create free account I already have an account

100 free credits when you connect your profile.